• A. Surface Reflectors and Portals
• B. Surface Reflectors and Reverb
• C. Diffraction
• D. Transmission
• E. Associate rooms to Surface Reflectors (Deprecated)

Note:

This page assumes you have already completed the Preparation for the Spatial Audio Tutorials as well as both Surface Reflectors Tutorial and Rooms and Portals Tutorial.

A. Surface Reflectors and Portals

Just like portals will open up a room area to let the sound propagate through it, it will also do the same through a reflective surface. At the end of the Surface Reflectors Tutorial, we noticed that reflections were occuring on openings of our mesh if we used simple cubes as surface reflectors. To fix this problem, Spatial Audio Portals are also aware of reflection paths and let them pass through. Reflection paths will even diffract on the borders of a portal.

1. Setup is simple, just placing a portal through a room and a surface reflector should do the trick.
   

   Reflection paths going through a Portal in the Game Object 3D Viewer

B. Surface Reflectors and Reverb

In a Room with late reverb, it is possible to feed early reflections into the reverb to make it more geometry aware.

1. In the Wwise project, open the Auxiliary Bus with the Reflect Effect applied to it.
   1. In the General Settings tab, make sure Use game-defined auxiliary sends is checked.
      

      Auxiliary Bus Property Editor General Settings tab to send early reflection to the room reverb
2. Play the scene and press the button in the small Room. With the player in the small Room, here is the Voices Graph we see:
   

   Early reflections in the small room are sent to the small room's reverb in the Voices Graph

C. Diffraction

When an object appears between the emitter and the listener, Spatial Audio can create diffraction paths that will go around the object. Depending on the angle of the path around an edge, the sound will be attenuated to simulate obstruction. You can enable diffraction per Sound and per Surface Reflector. An emitter emitting diffraction enabled sound will only diffract off a diffraction enabled reflective surface.

1. Enable diffraction on the Sound:
   • In the Positioning tab, make sure the Diffraction and Transmission option is selected.
     

     Enable Diffraction on the Sound
2. Adjust the diffraction curves in the sound's attenuation, or in the Project Settings. The diffraction curves in the Project Settings are used if the attenuation curves are set to "Use Project Diffraction", or if the sound doesn't have an attenuation.
   

   Diffraction curves in the Attenuation Editor
   

   Diffraction curves in the Project Settings

   See also

3. Enabling diffraction on an AkSurfaceReflector component:
   1. Check Enable Diffraction. This will generate diffraction edges on the geometry sent to Wwise Spatial Audio. The diffraction edges will be visible in the game object viewer when Wwise is connected to the game.
   2. You may also want to check Enable Diffraction On Boundary Edges. This checkbox appears when the previous checkbox is checked. Boundary edges are edges that are connected to only one triangle. For example, edges around the Unity Quad 3D Object would be considered boundary edges.
      

      Diffraction enabled AkSurfaceReflector
4. In the Wwise Unity Demo Scene, the outside emitter, the barrier and the exterior of the building are diffraction enabled. Diffraction paths are in purple. Each one of them will create a virtual source placed where the sound will be heard from.
   

   Diffraction paths in the Game Object 3D Viewer

   See also

   • Spatial Audio Diffraction
   • Using the Geometry API for Simulating Diffraction

D. Transmission

When an object appears between the emitter and the listener, the sound can also pass through the object. Spatial Audio models this phenomenon by filtering the direct path of the sound. When the emitter is in a room, the room's walls act like sound blocking objects. In this case, the direct and wet path of the sound are filtered to model transmission. Transmission loss values ranging from 0 to 1 can be applied to AkSurfaceReflector and AkRoom components. Typically, a value of 1.0 represents full loss of sound, and a value of 0.0 indicates that sound can be transmitted through the geometry unfiltered.

1. Enable transmission on the Sound:
   • In the Positioning tab, make sure the Diffraction and Transmission option is selected.
     

     Enable Transmission on the Sound
2. Adjust the transmission curves in the sound's attenuation, or in the Project Settings. The transmission curves in the Project Settings are used if the attenuation curves are set to "Use Project Transmission", or if the sound doesn't have an attenuation.
   

   Transmission curves in the Attenuation Editor
   

   Transmission curves in the Project Settings
   The sound will be filtered with the maximum transmission loss value of all surfaces sent from AkSurfaceReflector or AkRoom components that the sound encounters in a direct path from the emitter to the listener.
   1. On AkSurfaceReflector components, associate a transmission loss value for each submesh of the surface reflector mesh by populating the Transmission Loss Values array.
      

      Transmission Loss Values array on the AkSurfaceReflector component
   2. On AkRoom components, change the transmission loss value in the Transmission Loss parameter.
      

      Transmission Loss parameter on the AkRoom component

      See also

   • Spatial Audio Transmission
   • Rooms and Portal Transmission

E. Associate rooms to Surface Reflectors (Deprecated)

Warning: The Associated Room property of the AkSurfaceReflector component is deprecated and will be removed in a future version. We recommend not using it by leaving it set to None.

Each surface reflector added to Spatial Audio is analysed for diffraction edges and visibility. To optimize this step, each room can have a group of connected surface reflectors. Surface Reflectors associated with a room are not visible from other rooms. A Surface Reflector should be associated to a room if it is completely encompassed by it and if that room doesn't share surface reflectors with other rooms. Associating a room to a surface reflector is totally optional. If no room is selected, the surface reflector is added to a global group of surface reflectors. Associating surface reflectors to rooms will reduce the search space for ray casting performed by reflection and diffraction calculations.

1. Choose a Room under Associated Room in the AkSurfaceReflector component to associate them.
   

   AkSurfaceReflector with an Associated Room