Wwise Help

[name]

The name of the object.

Displays the object's color. Clicking the icon opens the color selector.

Select a color to apply it to the object.

	Note
	Selecting the square at the far left of the color selector causes the object to inherit its parent's color. When a color has been explicitly chosen for an object, it is displayed with the palette icon and a yellow triangle in the lower-right corner, as shown.

Controls the Mute and Solo states for the object and shows the implicit mute and solo states for the object.

Muting an object silences this object for the current monitoring session. Soloing an object silences all the other objects in the project except this one.

A bold M or S indicates that the Mute or Solo state has been explicitly set for the object. A non-bold M or S with faded color indicates that the object's Mute or Solo state was implicitly set from another object's state.

Muting an object implicitly mutes the descendant objects.

Soloing an object implicitly mutes the sibling objects and implicitly solos the descendant and ancestor objects.

	Tip
	Hold the Ctrl key while clicking a solo button to exclusively solo the object for which the solo button is associated.

	Note
	Mute and Solo are designed to be used for monitoring purposes only and are not persisted in the project or stored in the SoundBanks.

Indicates the number of elements in your project that contain direct references to the object. The icon is displayed in orange when references to the object exist, and in gray when no references exist.

Selecting the button opens the Reference View with the object's name in the References to: field.

Notes

Any additional information about the object properties.

Sets the display of the Property Editor's selected tabs. By default, there is one panel displaying only one selected tab. You can, however, click a splitter button to split the panel into two, either side by side or one on top of the other, for two different tabs. The currently selected option is highlighted with a background color.

	Note
	You cannot display the same tab in both panels. If you select the tab that is currently displayed in the other panel, then the other panel will automatically display another tab.

	Shortcuts for selecting tabs
	Press Ctrl and the number corresponding to the number of the Property Editor tab you want. For example, Ctrl+4 would select the RTPC tab if that were the fourth visible tab.

Bus Volume

The attenuation (level or amplitude) applied on the audio signal at the bus or Auxiliary Bus level. Refer to Understanding the Voice Pipeline for more information about volumes.

Default value: 0
Range: -200 to 200
Units: dB

	Note
	The default slider range is from -96 to +12. You can go over those limits by entering the value directly, or by rolling the mouse while the focus is on the edit control.

Bus Configuration

Determines in which configuration the bus output is formatted and can affect the processing status of the bus. You can use this setting to save CPU and memory by deferring mixing until further along the bus pipeline or reducing the number of channels for which Effects inserted on a bus must be processed.

Some of the available options are:

The Bus Configuration of any top-level bus, such as the Master Audio Bus, is automatically set to Defined by device. This is because these busses always inherit the bus configuration of the associated Audio Device.

For more information on these and other options in the drop-down list, refer to Understanding Bus Configurations .

Default value: Same as parent

(Meter)

A per channel peak meter. For more information about speaker configurations and channels, refer to Understanding Bus Configurations.

The signal level is green under -6 dB, yellow from -6 to 0 dB, and red over 0 dB.

The meter data source can be synchronized with the currently playing objects or, when a profiling session is present, with historical values. When the meter is showing the profiling session history, use the LIVE button on the Wwise toolbar to return to current values.

	Note
	Meters are not available on non-mixing busses. Refer to Understanding the Bus Icons and Processing Status for more information on the various processing statuses.

Processing

Displays the processing status of the bus based on how the project has been authored in Wwise; the processing status at runtime may differ. Refer to Understanding the Bus Icons and Processing Status for details on how the processing status is determined.

Bus Config.

Displays the bus configuration at the Pre-Effects stage based on how the project has been authored in Wwise; the bus configuration at runtime may differ.

When there is mixing on a bus, the Pre-Effects stage is after the mixing stage, but before any Effects are processed. For example, in the case of a bus with the bus configuration set to 2.0, all inputs are mixed to a stereo configuration, and then Effects are added to the stereo signal. The Bus Config. field displays the configuration of the bus between these two stages.

Out Config.

Displays the bus configuration at the Post-Effects stage (i.e., after both mixing and Effects have been processed). This is based on how the project has been authored in Wwise; the bus configuration at runtime may differ.

Because Effects have the ability to change the bus configuration, the Out Config. can differ from the Bus Config. For example, consider a bus with the Wwise Reflect plug-in. The Bus Config. could be 1.0, while its Out Config. would be Audio Objects.

If there are no Effects inserted on a bus, Bus Config. and Out Config. are equivalent. When there are Effects inserted on a bus, the Out Config. will indicate 'Unknown' unless you are profiling captured data from the sound engine. In this case, the actual Out Config. will be displayed.

Volume (to Output Bus)

The attenuation or amplitude of the signal routed to the audio output bus.

	Note
	The default slider range is from -96 to +12. You can go over those limits by entering the value directly, or by rolling the mouse while the focus is on the edit control.

	Tip
	When using the User-Defined Auxiliary Sends in a wet/dry mix scenario, the Output Bus Volume would be associated with the dry level, as opposed to the auxiliary send volume, which would relate to the wet level. Use an RTPC on Output Bus Volume and Auxiliary Send Volumes to control the balance from the game.

Default value: 0
Range: -200 to 200
Units: dB

Low-pass Filter (to Output Bus)

A Low-Pass Filter for the signal routed to the audio output bus.

A recursive filter that attenuates high frequencies based on the value specified.

The units for this filter represent the percentage of Low-Pass Filtering that has been applied, where 0 means no Low-Pass Filtering (signal unaffected) and 100 means maximal attenuation.

Default value: 0
Range: 0 to 100
Units: %

High-pass Filter (to Output Bus)

A High-Pass Filter for the signal routed to the audio output bus.

A recursive filter that attenuates low frequencies based on the value specified.

The units for this filter represent the percentage of High-Pass Filtering that has been applied, where 0 means no High-Pass Filtering (signal unaffected) and 100 means maximal attenuation.

Default value: 0
Range: 0 to 100
Units: %

Use game-defined auxiliary sends

Determines whether the object is using the game-defined auxiliary sends for the game object. A game-defined send is a combination of an Auxiliary Bus and a send volume.

Enable this option to have the object affected by the values coming from the game for the following functions:

If the game has initialized Spatial Audio and sent Rooms and Portals data to Wwise, this property determines if the object should send to the Auxiliary Bus defined by the current Room that the game object is inside.

Default value: false

Volume (Game-defined auxiliary sends)

Determines the attenuation on the game-defined auxiliary sends volumes set for the game object.

Use this volume to offset game-defined auxiliary send values.

	Note
	The default slider range is from -96 to +12. You can go over those limits by entering the value directly, or by rolling the mouse while the focus is on the edit control.

Default value: 0
Range: -200 to 200
Units: dB

Click the Configure Columns... shortcut (right-click) option from the column header band.

The Configure Columns Dialog opens. Specify which columns to display and their order.

ID column (User-Defined Auxiliary Sends)

Determines the ID of the User-Defined Auxiliary Sends. Up to 4 different sends can be added.

User Auxiliary Send

Determines the Auxiliary Bus this object is sending audio data to. Auxiliary sends can only target Auxiliary Busses.

To add an auxiliary send:

	Note
	Auxiliary Busses can be created anywhere in the Master-Mixer Hierarchy as children of an existing Bus or an existing Auxiliary Bus.

	Tip
	You can drag and drop an Auxiliary Bus object from the Project Explorer to the User-Defined Auxiliary Sends list to quickly add a send.

[...] column (User-Defined Auxiliary Sends)

Allow to select an Auxiliary Bus from the Master-Mixer Hierarchy.

User-Defined Auxiliary Send Volume

Determine the attenuation of the signal sent to the Auxiliary Bus.

	Note
	The default slider range is from -96 to +12 dB. You can go over those limits by entering the value directly, or by rolling the mouse while the focus is on the edit control.

	Note
	This control is only active when an Auxiliary Bus is selected for a specific send entry.

Default value: 0
Range: -200 to 200
Units: dB

Early Reflections Auxiliary Send

Enables reflection processing in Wwise Spatial Audio and determines the Auxiliary Bus this object is sending to for early reflections processing.

Early reflections processing simulates the acoustic phenomenon of sound bouncing off of virtual surfaces defined by geometry in the game. Since the first few reflections convey the most spatial information to the listener, it is advantageous to process the early reflections separately (from the late reverb) and with more detail using the Wwise Reflect plug-in.

To render early reflections, the Wwise Reflect plugin must be assigned to an effect slot on the Auxiliary Bus assigned to an early reflections send.

If no send is specified, then Wwise Spatial Audio will not compute early reflections paths for the sound.

	Note
	It is also possible to assign a reflections Auxiliary Bus per Game Object via the Spatial Audio API. In the case that a reflections bus is assigned both via the API and to the sound in the authoring tool, the bus used for the sound is taken from the authoring tool.

	Note
	For reflections to be computed, the Wwise Spatial Audio library must be initialized and the game must send level geometry to Wwise Spatial Audio.

To add an auxiliary send:

	Note
	Auxiliary Busses can be created anywhere in the Master-Mixer Hierarchy as children of an existing Bus or an existing Auxiliary Bus.

	Tip
	You can drag and drop an Auxiliary Bus object from the Project Explorer to the User-Defined Auxiliary Sends list to quickly add a send.

Early Reflections Auxiliary Send Volume

Determine the attenuation of the signal sent to the reflections Auxiliary Bus. This control also effects the volume of the reflections aux send specified by the API.

	Note
	The default slider range is from -96 to +12 dB. You can go over those limits by entering the value directly, or by rolling the mouse while the focus is on the edit control.

Default value: 0
Range: -200 to 200
Units: dB